DE NEEF® Denepox Rapid Gel

Two Component Epoxy Gel

Product Description

Denepox Rapid Gel is a non-sagging, rapid curing, 100% solids, two component, fast setting epoxy gel used for patching, surface sealing, and bonding substrates. Denepox Rapid Gel is a thixotropic gel with 1% elongation that works well for port adhesion and surface patching when injecting epoxies, especially if done the same day. Denepox Rapid Gel is moisture insensitive so it can be applied in damp or even wet conditions. This product meets ASTM C-881, Type: IV, Grade: 3, Class: A, B and C.

Product Applications

  • Surface patching
  • Surface sealing
  • Bonding substrates

Product Advantages

  • Fast setting
  • Low odor – no mercaptans
  • Moisture insensitive
  • No shrinkage
  • High strength
  • 100% solids
  • Easy to apply
  • Tenacious adhesion
  • Non-sag

Packaging & Handling


2 gallon units
10.5 oz side by side cartridges

Shelf Life: A minimum of 1 year in original, unopened container

Storage: Store in a dry area, between 40°F and 95°F. Protect from sunlight. 


Denepox Rapid Gel

Propety Part A Part B
Solids 100% 100%
Color White Black
Weight per gallon 13.97 lb 12.71 lb
Shelf Life 1 year 1 year
Property Mixed A and B Test
Blended Color Grey Visual
Mix Ratio by Volume 1:1 (A:B) N/A
Viscosity Non-Sag Gel N/A
Pot Life (3 oz. at 77° F) 4-5 min. N/A
Hardness (Shore D - 77° F) 75 D-2240
Gel Time (5 mil - 77° F) 15-20 min. N/A
Tensile Strength 6,000 psi D-638
Flexural Strength 4,000 psi D-790
Compressive Strength 10,880 psi D-695
Bond Strength (48 hrs.) 2,934 psi C-882
Elongation 1% D-638
Water Absorption (24 hrs 0.35% N/A

Note: The data shown above reflects typical results based on laboratory testing under controlled conditions. Reasonable variations from the data shown above may result.

Installation Guidelines

Surface of application should be clean and sound. The surface must be free of dust, oil, grease, laitance, curing compounds, or any other contaminants. It may be dry, damp, or wet, but must be free of standing water. The very best results are obtained on dry concrete. Do NOT apply on surfaces which have been sealed with a permanent type of form oil, curing compound or release agent. Remove these substances before application. The surface temperature must be 40°F and rising. Precondition the materials to between 65°F – 85°F before using. Refer to DE NEEF® Surface Preparation Guidelines for more details.

Mixing Procedure: Stir each component separately. Mix 1 part A with 1 part B by volume into a clean mixing container. Mix the epoxy with a slow speed drill with a mixing paddle attachment. Carefully scrape the sides and bottom of the pail during mixing with a paint stirring stick. Blend until a consistent color is observed. Mix only the amount of materials that can be used within the pot life. Please note: Large batches of epoxy will cure much faster than small batches. Mixed epoxy will cure much faster in hot weather than in cold weather.


Due to its very short pot life, Denepox Rapid Gel must be placed quickly. Best when applied in less than 25 mil thickness. For thicker applications use several thin layers. Allow cooling time before doing additional layers because of exothermic reaction.


Application at ambient temperature below 40°F is not recommended. Exposure to temperatures exceeding 150°F for prolonged periods is not recommended.

Health and Safety


Health Precautions:

Component A - IRRITANT - Prolonged skin or eye contact may cause sensitization and irritation.

Component B - CORROSIVE - Contact with skin or eyes may cause severe burns.

First Aid:

Skin Contact: Wash thoroughly with soap and water.

Eye Contact: Flush immediately with clean water and contact a physician.

Respiratory Problems: Remove affected person to fresh air immediately and contact a physician.

Hygiene: Wash hands immediately after use. Wash clothing before reuse.

Spills: Collect with absorbent material. Remaining material may be removed with a suitable solvent.

Disposal: Dispose of in accordance with local, stale and federal regulations.

Always use protective clothing, gloves and goggles consistent with OSHA regulations during use. Avoid eye and skin contact. Do not ingest. Refer to Safety Data Sheet for detailed safety precautions.

In the event of an EMERGENCY call:

CHEMTREC 800-424-9300. | North America customer service: 1-877-4AD-MIX (1-877-423-6491)

We hope the information here will be helpful. It is based on data and knowledge considered to be true and accurate, and is offered for consideration, investigation and verification by the user, but we do not warrant the results to be obtained. Please read all statements, recommendations, and suggestions in conjunction with our conditions of sale, which apply to all goods supplied by us. No statement, recommendation, or suggestion is intended for any use that would infringe any patent, copyright, or other third party right.

DE NEEF is a trademark, which may be registered in the United States and/or other countries, of GCP Applied Technologies Inc. This trademark list has been compiled using available published information as of the publication date and may not accurately reflect current trademark ownership or status.

© Copyright 2018 GCP Applied Technologies Inc. All rights reserved.

GCP Applied Technologies Inc., 62 Whittemore Avenue, Cambridge, MA 02140 USA.

In Canada, GCP Canada, Inc., 294 Clements Road, West, Ajax, Ontario, Canada L1S 3C6.

Ce document est à jour seulement à la date de la dernière mise à jour indiquée ci-dessous et n'est valide que pour une utilisation au Canada. Il est important que vous consultiez toujours les informations actuellement disponibles sur l'URL ci-dessous pour fournir les informations les plus récentes sur le produit au moment de l'utilisation. Des documents supplémentaires tels que les manuels de l'entrepreneur, les bulletins techniques, les dessins détaillés et les recommandations détaillées ainsi que d'autres documents pertinents sont également disponibles sur Les informations trouvées sur d'autres sites Web ne doivent pas être utilisées, car elles peuvent ne pas être à jour ou applicables aux conditions de votre site et nous déclinons toute responsabilité quant à leur contenu. S'il y a des conflits ou si vous avez besoin de plus d'informations, veuillez contacter le service client de GCP.

Last Updated: 2020-01-16