HYDRODUCT® 200

Pre-fabricated geocomposite layer for use on sub-structure without waterproofing

Product Description

HYDRODUCT® 200 is a strong preformed, 0.44 in. (11 mm) thick, geocomposite drainage sheet system. It is comprised of a hollow studded polystyrene core, covered on one side with a nonwoven, needle punched polypropylene filter fabric.

Product Advantages

  • Efficient water collector/deflector
  • Geotextile fabric filter
  • High flow capacity
  • Rot proof
  • Economical
  • Studded core

Uses

HYDRODUCT® 200 has been specially developed to provide a simple and highly practical collector and deflector of unwanted ground water on foundation walls, retaining walls, bridges, tunnels and planters. HYDRODUCT® 200 is acceptable for use with PREPRUFE®, however is not recommended for use over BITUTHENE® or PROCOR® waterproofing membranes.

HYDRODUCT® 200 has been designed to withstand ground pressures and the compaction forces of wet concrete to maintain a high water flow capacity. The drainage sheet must be connected into the site drainage system to minimize hydrostatic build-up and collect infiltrated water using HYDRODUCT® Coil 600 or traditional perforated pipes wrapped and linked with the geotextile filter fabric to prevent clogging.

Supply

HYDRODUCT®  VALUE
Roll size 4 ft x 50 ft (1.2 m x 15.2 m) 200 ft2 (18.6 m2)
Packaging 6 rolls/pallet
Weight 38 lbs (17.2 kg)/roll
COMPLEMENTARY MATERIALS VALUE
PREPRUFE® Detail Tape 2 in. x 50 ft (50 mm x 15 m) rolls
HYDRODUCT® Coil 600 50 ft (15.2 m) roll

Physical Properties

DRAINAGE CORE  TYPICAL VALUE TEST METHOD
Polymer High impact polystyrene  
Thickness 0.44 in. (11 mm) nominal ASTM C366 method B
Compressive strength 15,000 lbs/ft2 (718 kPa) ASTM D1621
Flow rate (gradient 1.0, load 172 kPa) 17 gal/min./ft (211 L/min./m) ASTM D4716
GEOTEXTILE  TYPICAL VALUE TEST METHOD
Type Nonwoven  
Polymer Polypropylene  
Weight 4.0 oz/yd2 (136 g/m2) ASTM D3776
Tensile strength 100 lbs (445 N) ASTM D4632
Apparent opening size 100 U.S. sieve (0.21 mm) ASTM D4751
Flow rate 165 gal/min./ft2 (6724 L/min./m2) ASTM D4491
CBR puncture 275 lbs (1.22 kN) ASTM D6241

Application Procedures

Safety, Storage and Handling Information 

All construction products must be handled properly. Safety Data Sheets (SDS) are available at gcpat.com and users should acquaint themselves with this information. Carefully read detailed precaution statements on product labels and the SDS before use.

Installation

In vertical applications, HYDRODUCT® 200 Drainage Composites can be applied to the substrate vertically or horizontally but, in either case, should extend from the perimeter discharge pipe to a point approximately 6 in. (150 mm) below the anticipated grade line.

HYDRODUCT® 200 should be attached to the substance with PREPRUFE® Detail Tape. When installing directly to concrete or wood, mechanical fasteners can be used. When using PREPRUFE® Detail Tape, press firmly to ensure good adhesion. Substrate and job site conditions will determine the attachment pattern. Additional consideration should be given in high wind exposures. Abut adjacent rolls with excess fabric overlapping in shingle fashion.

For inside and outside corners, abut adjoining drainage composite at the corner. Cover open core with extra geotextile filter fabric.

The exposed core along the top terminations should be covered with a strip of geotextile to prevent intrusion of soil into core. At the bottom termination extend the HYDRODUCT® 200 Drainage Composite out from the structure so that it passes behind and under the perimeter discharge pipe. Additional geotextile should be wrapped over the pipe to prevent soil intrusion.

To secure HYDRODUCT® 200 Drainage Composite around protrusions, apply PREPRUFE® Detail Tape around the protrusion in a picture frame configuration. Cut HYDRODUCT® 200 Composite to fit snugly around the protrusion. Press the cut edge firmly into PREPRUFE® Detail Tape.

HYDRODUCT® 200 should be covered promptly. Do not leave HYDRODUCT® 200 exposed to sunlight for more than two weeks. Motor vehicles, construction equipment or other trades should not be allowed directly on the HYDRODUCT® 200.

ca.gcpat.com | North America customer service: 1-877-4AD-MIX (1-877-423-6491)

We hope the information here will be helpful. It is based on data and knowledge considered to be true and accurate, and is offered for consideration, investigation and verification by the user, but we do not warrant the results to be obtained. Please read all statements, recommendations, and suggestions in conjunction with our conditions of sale, which apply to all goods supplied by us. No statement, recommendation, or suggestion is intended for any use that would infringe any patent, copyright, or other third party right.

BITUTHENE, HYDRODUCT, PREPRUFE, and PROCOR are trademarks, which may be registered in the United States and/or other countries, of GCP Applied Technologies Inc. This trademark list has been compiled using available published information as of the publication date and may not accurately reflect current trademark ownership or status.

© Copyright 2018 GCP Applied Technologies Inc. All rights reserved.

GCP Applied Technologies Inc., 62 Whittemore Avenue, Cambridge, MA 02140 USA.

In Canada, 294 Clements Road, West, Ajax, Ontario, Canada L1S 3C6.

Ce document est à jour seulement à la date de la dernière mise à jour indiquée ci-dessous et n'est valide que pour une utilisation au Canada. Il est important que vous consultiez toujours les informations actuellement disponibles sur l'URL ci-dessous pour fournir les informations les plus récentes sur le produit au moment de l'utilisation. Des documents supplémentaires tels que les manuels de l'entrepreneur, les bulletins techniques, les dessins détaillés et les recommandations détaillées ainsi que d'autres documents pertinents sont également disponibles sur www.ca.gcpat.com. Les informations trouvées sur d'autres sites Web ne doivent pas être utilisées, car elles peuvent ne pas être à jour ou applicables aux conditions de votre site et nous déclinons toute responsabilité quant à leur contenu. S'il y a des conflits ou si vous avez besoin de plus d'informations, veuillez contacter le service client de GCP.

Last Updated: 2018-12-12

https://ca.gcpat.com/fr-ca/solutions/products/hydroduct-drainage-composite/hydroduct-200