PIERI® EURO-TARD™

In-form retarder

Product Description

PIERI® EURO-TARD™ is a one-step, general-purpose in-form retarder with excellent heat resistance.  Available in 10 depths of etch, each one color and number coded for safety and convenience. A test panel simulating job conditions should be poured for proper grade selection. Coverage: approximately 350 ft2/gal.

Product Advantages

  • One coat, fast drying
  • High heat resistance
  • Excellent etch retention
  • High coverage rates, low cost per ft2

Area of Application

Excellent for architectural finish precast or poured-in-place concrete. Placement time up to 30 minutes. Heat resistance up to 150°F. For use with steel, concrete, plywood, plastic and many latex forms. Note that plywood forms should be sealed before use (see #245 Form Seal).

EURO-TARD® Grade Guide

EST. ETCH-DEPTH* GRADE
Acid Etch 03 Light Violet
Sand Blast 05 Powder Blue Violet
Up to 1/4 in. (Up to 6.5 mm) 15 Yellow
1/8 to 1/4 in. (3.0 to 6.5 mm) 25 Beige
1/8 to 3/8 in. (3.0 to 9.5 mm) 50 Canary Green
1/8 to 3/8 in. (3.0 to 9.5 mm) 75 Blue
3/8 to 1/2 in. (9.5 to 13 mm) 100 Gray
3/8 to 5/8 in. (13 to 16 mm) 125 Pink
3/8 to 5/8 in. (13 to 16 mm) 150 Green
1 to 3/2 in. (25 to 38 mm) 250 Orange

*564 lbs/yd3 or 355 kg/m3 of cement.

Directions

Thoroughly mix before application. Uniformly coat form with a single coat of PIERI® EURO-TARD™ (or two light coats) using brush, roller, or airless sprayer at a rate of 350 ft2/gal (4 mils). Clean up with Arca Solv or Xylene. Allow retarder to dry thoroughly (approximately 20 minutes depending on temperature and humidity) before pouring concrete.

Caution: When steam curing, bring the temperature up gradually to allow the surface retarder to react properly with the concrete.

Note: If steam is to be used, it should also be used with the test panel poured for the proper grade selection. Wash off at the end of the curing cycle with high pressure water. Mold can be cleaned with a scraper of stiff broom or Euro-Clean (a solvent based neutralizer/ retarder remover).

Technical Data

Solvent-based. Flash point 30°F. Heat resistance up to 150°F. See EURO-TARD™ Grade Guide Section for help in etch selection. Meets EPA’s VOC requirements for Non-photochemically reactive compounds.

Shelf life and Storage

One year from manufacturing date in closed original container.

Packaging

Available in 5 gallon steel pails.

Safety

Highly flammable.

Keep away from heat, sparks and open flames.

Use respirator for spray applications.

Shipping Classification

Paint, 3, UN1263, Flammable Liquid, P.G. II.

 

ca.gcpat.com | North America customer service: 1-877-4AD-MIX (1-877-423-6491)

We hope the information here will be helpful. It is based on data and knowledge considered to be true and accurate and is offered for consideration, investigation and verification by the user, but we do not warrant the results to be obtained. Please read all statements, recommendations and suggestions in conjunction with our conditions of sale, which apply to all goods supplied by us. No statement, recommendation or suggestion is intended for any use that would infringe any patent, copyright or other third-party right.

PIERI is a trademark, which may be registered in the United States and/or other countries, of GCP Applied Technologies, Inc. This trademark list has been compiled using available published information as of the publication date and may not accurately reflect current trademark ownership or status.

© Copyright 2018 GCP Applied Technologies, Inc. All rights reserved.


GCP Applied Technologies Inc., 2325 Lakeview Parkway, Suite 475, Alpharetta, GA 30009, USA
GCP Canada, Inc., 294 Clements Road, West, Ajax, Ontario, Canada L1S 3C6.
This document is only current as of the last updated date stated below and is valid only for use in the Canada. It is important that you always refer to the currently available information at the URL below to provide the most current product information at the time of use. Additional literature such as Contractor Manuals, Technical Bulletins, Detail Drawings and detailing recommendations and other relevant documents are also available on www.gcpat.com. Information found on other websites must not be relied upon, as they may not be up-to-date or applicable to the conditions in your location and we do not accept any responsibility for their content. If there are any conflicts or if you need more information, please contact GCP Customer Service.

Last Updated: 2024-06-21

https://ca.gcpat.com/en/solutions/products/pieri-architectural-precast-portfolio/pieri-euro-tard