STRUX® 90/40 synthetic macro fiber reinforcement is a unique form of high strength, high modulus synthetic macro reinforcement that is evenly distributed throughout the concrete matrix. STRUX® 90/40 adds toughness, impact and fatigue resistance to concrete. Unlike traditional microfiber reinforcement,
STRUX® 90/40 is specifically engineered to provide high, post-crack control performance. Reinforced concrete with STRUX® 90/40 has been shown to reliably achieve residual flexural strength values in excess of 150 psi (1.0 MPa) at dosages that can easily be batched and finished. It consists of synthetic macro fibers 1.55 in. (40 mm) in length with an aspect ratio of 90 that have specifically been designed to replace welded wire fabric, steel fibers and light rebar reinforcement in slab-on-ground flooring, thin-walled precast applications and composite steel floor deck assemblies. STRUX® 90/40 is a user-friendly fiber reinforcement which is easier and safer to use, compared to these other types of reinforcement.
- Savings from lower labor costs and fewer construction days
- Enhances safety by eliminating handling of steel fibers, welded wire fabrics or light rebar
- Eliminates concerns of proper positioning of reinforcement
- Provides superior crack control due to the geometry and elastic modulus
- Corrosion Resistant (non-ferric)
- Controls plastic and long term drying shrinkage cracks
STRUX® 90/40 is specially designed for ease of use, rapid dispersion, good finishability and improved pumpability in slabon-ground flooring and many precast applications. STRUX® 90/40 may be used in commercial, industrial, and residential floors, as well as other flat work and form work applications. The addition rate of STRUX® 90/40 can be easily calculated using GCP’s SDS Software, using several factors such as compressive strength of concrete, modulus of sub-grade reaction, thickness of concrete and applied loads. Please consult your GCP Applied Technologies sales representative for proper addition rate of STRUX 90/40 for your application. Always consult local building codes (refer to Engineering Bulletin 1).
Composite Steel Floor Deck for Normal and Lightweight Concrete
STRUX® 90/40 can be used as a suitable alternative to WWF or light reinforcing steel specified for temperature and shrinkage reinforcement for composite steel floor decks assemblies. STRUX® 90/40 complies with American National Standards Institute/ Steel Deck Institute (ANSI/SDI C-1.0) design code provision for minimum reinforcing at the minimum addition rate of 4 lbs/yd3 (2.4 kg/m3). STRUX® 90/40 is UL (U.S.) and ULC (Canada) classified with fire ratings up to 2 hours for D700, F700, D800, F800, D900 and F900 except 909 at a maximum addition rate of 5 lbs/yd3 (3.0 kg/m3).
Compatibility with Other Admixtures and Batch Sequencing
STRUX® 90/40 is compatible with all GCP admixtures. Their action in concrete is mechanical and will not affect the hydration process of the cement or compressive strength. Each liquid admixture should be added separately to the concrete mix.
|STRUX® 90/40 PROPERTIES|
|Modulus of elasticity||1,378 ksi (9.5 GPa)|
|Tensile strength||90 ksi (620 MPa)|
|Melting point||320°F (160°C)|
|Ignition point||1,094°F (590°C)|
|Alkali, acid & salt resistance||High|
STRUX® 90/40 is available in 1.0 lb or 5.0 lb (0.5 kg or 2.3 kg) Concrete-Ready™ bags.
Note: The results shown represent the behavior of STRUX® 90/40 fibers in concrete with an average cylinder compressive strength of 4,000 psi (28 MPa).
The residual flexural strength depends primarily on the type of fibers and the dosage rates at which they are added to the concrete.
Furthermore, GCP Applied Technologies Inc. has found that fiber performance also depends on the strength of the concrete. GCP Applied Technologies Inc. has performed extensive laboratory testing to cover the compressive strength range of practical interest i.e. concrete strength 2,500 to 6,500 psi (17 to 45 MPa).
STRUX 90/40 addition rates are dependent on the specific application and desired properties and will typically vary between 3 to 8 lbs/yd3 (1.8 to 4.8 kg/m3) but could go higher.
The utilization of STrUX® 90/40 may require the use of a mid-range water reducer or a superplasticizer such as MIRA® or ADVA® to restore the required workability. In addition, slight increases in fine aggregate contents may be needed.
STRUX® 90/40 may be added to concrete at any point during the batching or mixing process. After fiber addition, the concrete must be mixed at the minimum of 70 revolutions to ensure adequate dispersion.
Please contact your GCP Applied Technologies representative with any questions. For more detailed instructions refer to Technical Bulletin TB-1200.
ca.gcpat.com | North America customer service: 1-877-4AD-MIX (1-877-423-6491)
We hope the information here will be helpful. It is based on data and knowledge considered to be true and accurate and is offered for consideration, investigation and verification by the user, but we do not warrant the results to be obtained. Please read all statements, recommendations and suggestions in conjunction with our conditions of sale, which apply to all goods supplied by us. No statement, recommendation or suggestion is intended for any use that would infringe any patent, copyright or other third-party right.
ADVA, MIRA, and STRUX are trademarks, which may be registered in the United States and/or other countries, of GCP Applied Technologies Inc. This trademark list has been compiled using available published information as of the publication date and may not accurately reflect current trademark ownership or status.
© Copyright 2018 GCP Applied Technologies Inc. All rights reserved.
GCP Applied Technologies Inc., 62 Whittemore Avenue, Cambridge, MA 02140, USA
GCP Canada, Inc., 294 Clements Road, West, Ajax, Ontario, Canada L1S 3C6
Ce document est à jour seulement à la date de la dernière mise à jour indiquée ci-dessous et n'est valide que pour une utilisation au Canada. Il est important que vous consultiez toujours les informations actuellement disponibles sur l'URL ci-dessous pour fournir les informations les plus récentes sur le produit au moment de l'utilisation. Des documents supplémentaires tels que les manuels de l'entrepreneur, les bulletins techniques, les dessins détaillés et les recommandations détaillées ainsi que d'autres documents pertinents sont également disponibles sur www.ca.gcpat.com. Les informations trouvées sur d'autres sites Web ne doivent pas être utilisées, car elles peuvent ne pas être à jour ou applicables aux conditions de votre site et nous déclinons toute responsabilité quant à leur contenu. S'il y a des conflits ou si vous avez besoin de plus d'informations, veuillez contacter le service client de GCP.
Last Updated: 2018-12-12